How To Put Freon In Toyota Rav4

Toyota RAV4 Service Transmission: Replacement

1. belch refrigerant from refrigeration organisation

1. Get-go up the engine.
2. Turn the a/c switch on.
3. Operate the cooler compressor with an engine speed of approximately 1,000 rpm for v to 6 minutes to broadcast the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.
4. Cease the engine.
5. Using sst, discharge the refrigerant gas.

   Sst 07110-58060 (07117-58060, 07117-58070, 07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)

2. Charge refrigerant

1. Perform vacuum purging using a vacuum pump.
2. Charge refrigerant hfc-134a (r134a).

Standard: 430 +-30 g (15.ii +-1.1 Oz.)

Sst 07110-58060 (07117-58060, 07117-58070, 07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)

Discover:

• Practice not operate the cooler compressor earlier charging refrigerant every bit the cooler compressor will not piece of work properly without any refrigerant, and volition overheat.
• Approximately 100 thou (3.53 Oz.) Of refrigerant may need to be charged after bubbles disappear. The refrigerant corporeality should be checked by measuring its quantity, and not with the sight glass.

3. Warm up engine

1. Warm up the engine at less than i,850 rpm for 2 minutes or more after charging the refrigerant.

Notice:

Be sure to warm up the compressor when turning the a/c switch on later removing and installing the libation refrigerant lines (including the compressor), to prevent damage to the compressor.

4. Bank check for leakage of refrigerant

1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.
2. Perform the performance under these conditions:

• Stop the engine.
• secure good ventilation (the gas leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or frazzle gas).
• Repeat the test 2 or 3 times.
• Brand certain that some refrigerant remains in the refrigeration system. When compressor is off: approximately 392 to 588 kpa (four to 6 kgf/cm2, 57 to 85 psi)

3. Using a gas leak detector, check the refrigerant line for leakage.
4. If a gas leak is not detected on the drain hose, remove the blower motor control (blower resistor) from the cooling unit. Insert the gas leak detector sensor into the unit and perform the examination.
5. Disconnect the connector and leave the force per unit area switch on for approximately 20 minutes. Bring the gas leak detector shut to the pressure switch and perform the test.

On-vehicle inspection

Audit refrigerant pressure level with manifold guess set This method uses a manifold gauge fix to locate problem areas. Read the manifold gauge pressure when these weather are establishe ...

Other materials:

Problem symptoms tabular array (2005/xi-2006/01)
Hint: Use the table below to help make up one's mind the crusade of the problem symptom. The potential causes of the symptoms are listed in society of probability in the "suspected area" column of the table. Bank check each symptom by checking the suspected areas in the society they are listed. Replace p ...

Removal (2005/xi-2006/01)
Remove forepart wheel Drain automatic transaxle fluid Drain the automatic transaxle fluid for u140f (see page ax-147). Drain the automatic transaxle fluid for u241e (run across page ax-146). Remove front axle hub nut (run into page ah-6) Disconnect front speed sensor lh (run into page bc-191) ...

Terminals of ecu
Check tire pressure warning ecu Disconnect the e56 ecu connector. Measure the voltage and resistance of the wire harness side connector. If the result is not equally specified, at that place may be a malfunction on the wire harness side. Reconnect the e56 ecu connector. Measure the ...

Source: https://www.trav4.net/replacement-863.html

Share this post